Appointment Lookup
646-440-2692
Whirlpool Washer won't stop filling
Common reasons your Whirlpool Washer won't stop filling
The most common reasons your Whirlpool washer won't stop filling are a clogged water valve, a bad water-level pressure switch, or a malfunctioning electronic control board.
40% of the time it's the Water Valve
29% of the time it's the Water Level Switch
12% of the time it's the Electronic Control Board
19% of the time it's the Something else
Schedule your washer repair now!
We can help! Our service technicians have repaired over 10,000 Whirlpool washers. We can fix yours no matter where you bought it.
Most common repairs needed to fix a Whirlpool washer
Water Valve Replacement
The water valve assembly controls water flow into the washer. A clogged water valve inlet screen will prevent the wash tub from filling with hot water, cold water, or both. Electrical failures in the valve may also prevent the valve from opening to allow water into the tub. The valve connects your home's water supply to the washer. A faulty valve may begin leaking into the tub or around the connections to the water supply hoses. If you suspect a faulty water valve assembly, have a Sears Home Services professional inspect the washer and replace the valve if needed.
Water Level Switch Replacement
If the water-level pressure switch in a washer is bad, it loses its ability to sense, control, and maintain the water level in the outer wash tub. This failure may result in the washer not filling or overfilling with water. The pressure switch operates using an air tube attached to the bottom of the tub, which senses the water level. As the wash tub fills, air pressure in the tube pushes up on a diaphragm inside the water-level pressure switch. A post attached to the diaphragm opens and closes electrical contacts within the switch's body, thereby controlling the water fill and shutting off the water when the washer is full. If any components of the water-level pressure switch fail, have a Sears Home Services repair technician replace the switch.
Electronic Control Board Replacement
A malfunctioning electronic control board can lead to various failures in a washer. This is because the board serves as the brain of the washer, controlling crucial components such as the water valve, drive motor, drain pump, and cycles. If the electronic control board fails, the washer may not power up or display the cycle status. Additionally, it might fail to fill, agitate, spin, or drain. In some cases, a shorted board may emit a burning smell. How to replace the electronic control board in a washer https://www.searspartsdirect.com/diy/repair-guide/how-to-replace-the-electronic-control-board-on-a-top-load-washer
Why won't my Whirlpool washer stop filling?
First, shut off the water supply faucets behind the washer when you discover that the machine is filling constantly.
When your Whirlpool washer won’t stop filling with water, a leaking water inlet valve is often causing the problem. A bad electronic control board or timer could also cause this problem.
Testing the Water Inlet Valves
Because a control board or timer problem can also cause a constant filling failure, you’ll need to perform this quick test to determine whether a leaking water inlet valve is causing the problem.
- Unplug the washer power cord to completely disconnect electrical power to isolate the water valves so there’s no chance that they can receive electrical current from a defective control board or timer.
- Open the water supply faucets behind the washer.
- Check water level inside the washer to see if the machine fills with power disconnected.
- Shut the water supply faucets once you determine whether the washer continues to fill with water.
If the washer fills with its power cord unplugged, then you know that leaking water inlet valves are causing the constant filling failure.
For a front-load washer, follow the steps in this DIY repair video to replace the water inlet valve assembly:
For a top-load washing machine, follow the procedure shown in this video to replace the inlet water valve assembly:
Here’s a video that shows how to replace the water inlet valve assembly in some top-load washers that house the water inlet valve assembly inside the control console:
If you’re unable to replace the water inlet valve assembly on your own, schedule washer repair service to have a Sears Home Services technician visit your home and install a new water valve assembly.
Testing the Control System
If the washer doesn’t fill constantly with its power cord unplugged, then the control system is likely causing the failure by sending voltage to the water valve assembly while the washer is turned off.
To verify this failure, plug the washer power cord in and open the water supply faucets behind the washer to determine whether the washer fills constantly.
If water enters the washer with the control turned off, you’ll need to unplug the washer power cord and replace the electronic control board or timer.
What to expect when you experience a Whirlpool washer won't stop filling issue
How is the washer won't stop filling issue fixed?
Correcting most washer won't stop filling problems usually involves replacing the water valve, water-level pressure switch, or electronic control board. However, there are many potential causes, so a thorough diagnosis is key to fixing the problem. An accurate diagnosis is essential to understanding how much the repair will be.
Sears Home Services recommendations for a washer won't stop filling problem
When a washer won't stop filling, it can be for many reasons. To avoid replacing unneeded parts, we recommend having a Sears Home Services professional perform diagnostic tests to identify the root cause of the problem. Our technicians are experienced at diagnosing all types of washer failures.
What to look out for with a washer won't stop filling diagnosis
Diagnosing modern appliances without proper knowledge and training can be difficult. Without using proper diagnostic techniques, fixing your washer problem will only be achieved through changing parts on a hunch. Appliances, especially in the last 10 years, have become extremely advanced, and many models have electronic parts that are difficult to test. DIY repairs on the latest appliance models are becoming increasingly difficult.
A Whirlpool washer that won’t stop filling risks flooding your laundry area. A stuck inlet valve or faulty water-level sensor commonly triggers the overflow. Rather than watching water spill, enlist a washer maintenance near me. Proper level control ensures safe, efficient washes.
What our customers say about us
With more than 1.3 Million 5 Star Reviews, you don't have to take our word for it
Thanks
Thanks for your expert analysis of the problem that caused the flooding of my home .I was scared the first few times I used the machine , but all is working great.
Frank U, Coconut Creek, FL
Excellent service.
Pleasant person to work with. He explains things to you.
Jacklyn J, Bessemer, AL
Very Professional
Very professional, thoughtful and knowledgeable I would highly recommend him.
Marilyn W, Covington, LA
Frequently Asked Questions
Repair Washer Resources
Decode your Whirlpool Cabrio washer error codes easily with our comprehensive guide. Get your washer running smoothly today!
Learn how to quickly and easily fix the OE error code on your LG washer and prevent future problems.
Having trouble with your washer? Find out why won’t my washer drain and learn how to fix it quickly with Sears Home Services.
Learn the common causes of a washing machine leaking water from underneath and how you can fix the problem.
Glossary Terms
Hard water is water that contains high levels of dissolved minerals, particularly calcium and magnesium. It contrasts with soft water, which has lower concentrations of these minerals.
A washing machine pedestal is a platform that raises the washer off the ground, providing easier access to the appliances and often includes additional storage space such as drawers.
A washer tub is the interior part of a washing machine where clothes are placed for washing, typically made of stainless steel, plastic, or porcelain-coated metal, designed to hold water and withstand the agitation or spinning during the wash cycle.
Fabric softener is a laundry additive used to soften and freshen clothing, reduce static cling, and make fabrics feel smoother.